INTERSEAL 670HS MSDS PDF

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Zulumuro Gugul
Country: Tunisia
Language: English (Spanish)
Genre: Art
Published (Last): 18 May 2005
Pages: 302
PDF File Size: 1.40 Mb
ePub File Size: 1.75 Mb
ISBN: 978-1-54163-461-8
Downloads: 49313
Price: Free* [*Free Regsitration Required]
Uploader: Akir

Press and move to zoom. Preferred application is by a suitable large tip hopper gun e.

Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. Puddles, ponding and accumulations of water must be removed. Intrseal, these phenomena are not detrimental to anti-corrosive performance. Soluble salts should be removed by fresh water washing. Alternatively, a broadcast method of application can be used.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Avoid using a mixture of application methods whenever possible. Prior to paint application all surfaces should be assessed and treated in accordance with ISO With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS.

  ATG DYNAMO PDF

Typically this would apply to C or D grade rusting in this standard. Be the first to write a review for this product!

Once the unit has been mixed it must be used within the working pot life specified. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used. Loose or flaking coatings should be removed back to a firm edge.

When applying by methods other than airless spray, the required film build is unlikely to be achieved. Certification is for tanks greater than gallons Always mix a complete unit in the proportions supplied.

However, it can be used over suitably primed surfaces. A low Lnterseal, two component high build, high solids surface tolerant epoxy maintenance coating. Do not thin more than allowed by local environmental legislation. Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems.

In common with all epoxies Interseal HS will chalk and discolor on exterior mssd. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. NSF Certification is for tanks greater than gallons It is also possible to apply to damp surfaces in some circumstances.

Accumulated dirt and soluble salts must be removed. Typical thicknesses will be between milsmicrons. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates.

  IFR 2945A PDF

INTERSEAL HS PLATINUM GREY MSDS Download

Application should then be to a suitably primed surface. Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. Low or high temperatures may require specific application techniques to achieve maximum film build. Level of sheen and surface finish is dependent on application method.

Dry bristle brushing will normally be adequate for accumulated dirt. Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. Please consult International Protective Coatings for alternative recommendations.

670sh surface profile of mils microns is recommended. Sagola or Air texture gun fitted with a mm nozzle. Further information is available from International Protective Coatings. Varnish Hybrid Water base. Mouse over image to zoom. Premature exposure to ponding water will cause a color change, especially intereal dark colors. Consult International Protective Coatings for further details.

Surface preparation The performance of this product will depend upon the degree of surface preparation. Trowel or roller can be used for small areas. The surface to be coated should be clean, dry and free from contamination.